We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

    PPG - Sigmacover 410 - Epoxy Coating

    Review (0)
    £310.70
    Tax excluded
    £372.84 Tax incl.

    PPG - Sigmacover 410 - Epoxy Coating is a two component, high solids, high build, epoxy coating designed for general purpose protection of steel and concrete structures exposed to atmospheric land or marine conditions.

    Size :
    Standard Colours :
    Quantity :
    • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
    • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

    PPG - Sigmacover 410 - Epoxy Coating is a two component, high solids, high build, epoxy coating designed for general purpose protection of steel and concrete structures exposed to atmospheric land or marine conditions.

    Features

    • General-purpose epoxy buildcoat in protective coating systems, for steel and concrete structures exposed to
      atmospheric land or marine conditions
    • Excellent durability
    • Can be recoated with various two-component and conventional coatings, even after long weathering periods
    • Easy application by airless spray
    • Good drying- and curing properties at low substrate temperature (down to –5°C (23°F))

    Recommended Substrate Conditions and Temperatures

    Substrate conditions

    • Suitable primer must be dry and free from any contamination
    • Surface of previous coat should be sufficiently roughened if necessary
    • When applied to zinc silicate, a mist coat and full coat technique is required

    Substrate temperature

    • Substrate temperature during application and curing down to -5°C (23°F) is acceptable; provided the substrate is free from ice and dry
    • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point

    Instructions for use

    Mixing ratio by volume: base to hardener 80:20 (4:1)

    • The temperature of the paint should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity
    • Adding too much thinner results in reduced sag resistance

    Airless spray

    Recommended thinner

    THINNER 91-92

    Volume of thinner

    0 - 10%

    Nozzle orifice

    Approx. 0.46 – 0.53 mm (0.018 – 0.021 in)

    Nozzle pressure

    20.0 - 25.0 MPa (approx. 200 - 250 bar; 2901 - 3626 p.s.i.)

    Brush/roller

    • Application by brush may show brush marking, due to the thixotropic nature of the paint and is most suitable to small areas, tight angle areas or for stripe coating or touch-up
    • Application by roller will leave roller marking and is suitable for minimum DFT requirements only
    • A roller suitable for epoxy application must be used

    Recommended thinner

    THINNER 91-92

    Volume of thinner

    0 – 5%

    Cleaning solvent

    THINNER 90-53

    PPG Paints
    PPG-S41

    Data sheet

    Type
    Epoxy
    Size
    20L
    Colour
    MIO Light Grey (Sigma 9110)
    OffWhite
    Finish
    Flat
    Coverage
    10.7 m²/l for 75 µm (428 ft²/US gal for 3.0 mils
    For Use On
    steel and concrete
    Application Method
    Brush, Roller & Spray
    Recoat Time (20°c)
    8hrs

    Specific References

    No customer reviews for the moment.

    Write your review
    PPG - Sigmacover 410 - Epoxy Coating

    You might also like

    16 other products in the same category:

    arrow_back
    arrow_forward

    PPG - Sigmacover 410 - Epoxy Coating

    £310.70
    Tax excluded
    £372.84 Tax incl.