We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

  • New
Rustoleum - Hard Hat - Fluorescent Topcoat
  • Rustoleum - Hard Hat - Fluorescent Topcoat
  • Rustoleum - Hard Hat - Fluorescent Topcoat

Rustoleum - Hard Hat - Fluorescent Topcoat

Review (0)
£11.24
Tax excluded
£13.49 Tax incl.

Rustoleum Hard Hat® Aerosol Topcoats 2200 are based on a fast drying short oil soya alkyd. The products are based on lead and chromate free pigments.

Fluorescent Colours :
Quantity :
  • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
  • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

Rustoleum Hard Hat® Aerosol Topcoats 2200 are based on a fast drying short oil soya alkyd. The products are based on lead - and chromate free pigments.

Features:

  • Highly visible fluorescent coatings
  • Ideal for railings, signs, colour coding etc.
  • First apply matt white 2190 for best results
  • Finish with transparent topcoat for better gloss
  • To handle after 30 minutes (at 20°C)

Recommended Use

RUST-OLEUM Fluorescent Topcoats 2200 should be applied over RUST-OLEUM Hard Hat 2190 Flat White; for exterior applications it is recommended to recoat Fluorescent Topcoats 2200 with RUST-OLEUM Hard Hat 2500 Clear. RUST-OLEUM Fluorescent Topcoats 2200 are intended for safety marking or signalling. RUST-OLEUM Fluorescent Topcoats 2200 should be used in light industrial exposures, normal humidity and interior applications.

Surface Preperation

Remove dirt, grease, oil and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application.

Application Conditions

For good results the relative humidity shall be below85% and the temperature of the can and substrate above 0°C.

Application & Thinning: Aerosol

Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 25 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 - 3 seconds to clean valve.

Technical Data

Gloss Level: Matt Heat Resistance: 100°C (dry heat)

Dry Times By 20º C/RV 50%

Touch dry: 15 minutes

Dry to handle: 30 minutes

Dry to recoat: After 1 hour

Fully cured: 3 days

Recommended Wet Film Thickness 

100 µm

Recommended Dry Film Thickness

25 µm

Theoretical Coverage

2.1 m² per spray can at 25 µm dry

Practical Consumption 

Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Rustoleum
RUS-FT

Data sheet

Type
Aerosol
Size
500ML
Colour
Fluorescent Blue, Fluorescent Green, Fluorescent Red, Fluorescent Yellow and Fluorescent Orange
Finish
Matt
Coverage
2.1 m² per spray can at 25 µm dry
For Use On
Ideal for railings & signs
Application Method
Spray
Recoat Time (20°c)
1hr
Interior/Exterior
Exterior

Specific References

No customer reviews for the moment.

Write your review
Rustoleum - Hard Hat - Fluorescent Topcoat

12 other products in the same category:

arrow_back
arrow_forward
Rustoleum - Hard Hat - Fluorescent Topcoat

Rustoleum - Hard Hat - Fluorescent Topcoat

£11.24
Tax excluded
£13.49 Tax incl.