We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

    Rustoleum - Hard Hat - Fluorescent Topcoat
    • Rustoleum - Hard Hat - Fluorescent Topcoat
    • Rustoleum - Hard Hat - Fluorescent Topcoat

    Rustoleum - Hard Hat - Fluorescent Topcoat

    Review (0)
    £13.24
    Tax excluded
    £15.89 Tax incl.
    Delivered Within 3-5 Days

    Rustoleum Hard Hat® Aerosol Topcoats 2200 are based on a fast drying short oil soya alkyd. The products are based on lead and chromate free pigments.

    Fluorescent Colours :
    Quantity :
    • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
    • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

    Rustoleum Hard Hat® Aerosol Topcoats 2200 are based on a fast drying short oil soya alkyd. The products are based on lead - and chromate free pigments.

    Features:

    • Highly visible fluorescent coatings
    • Ideal for railings, signs, colour coding etc.
    • First apply matt white 2190 for best results
    • Finish with transparent topcoat for better gloss
    • To handle after 30 minutes (at 20°C)

    Recommended Use

    RUST-OLEUM Fluorescent Topcoats 2200 should be applied over RUST-OLEUM Hard Hat 2190 Flat White; for exterior applications it is recommended to recoat Fluorescent Topcoats 2200 with RUST-OLEUM Hard Hat 2500 Clear. RUST-OLEUM Fluorescent Topcoats 2200 are intended for safety marking or signalling. RUST-OLEUM Fluorescent Topcoats 2200 should be used in light industrial exposures, normal humidity and interior applications.

    Surface Preperation

    Remove dirt, grease, oil and all other surface contaminants by appropriate means. Sand intact coatings to roughen the surface slightly. The surface must be clean and dry during application.

    Application Conditions

    For good results the relative humidity shall be below85% and the temperature of the can and substrate above 0°C.

    Application & Thinning: Aerosol

    Remove cover cap. Shake vigorously for at least one minute after the rattle of mixing ball is heard. Shake frequently during use. Hold can approx. 25 cm from surface. Use back and forth motion keeping can parallel with surface. Ensure that can is in motion when spray button is pressed to avoid runs and sags. Apply several thin layers at a few minutes interval to achieve adequate coating thickness. After use turn can upside down and press spray button for 2 - 3 seconds to clean valve.

    Technical Data

    Gloss Level: Matt Heat Resistance: 100°C (dry heat)

    Dry Times By 20º C/RV 50%

    Touch dry: 15 minutes

    Dry to handle: 30 minutes

    Dry to recoat: After 1 hour

    Fully cured: 3 days

    Recommended Wet Film Thickness 

    100 µm

    Recommended Dry Film Thickness

    25 µm

    Theoretical Coverage

    2.1 m² per spray can at 25 µm dry

    Practical Consumption 

    Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

    Rustoleum
    RUS-FT

    Data sheet

    Type
    Aerosol
    Size
    500ML
    Colour
    Fluorescent Blue, Fluorescent Green, Fluorescent Red, Fluorescent Yellow and Fluorescent Orange
    Finish
    Matt
    Coverage
    2.1 m² per spray can at 25 µm dry
    For Use On
    Ideal for railings & signs
    Application Method
    Spray
    Recoat Time (20°c)
    1hr
    Interior/Exterior
    Exterior

    Specific References

    No customer reviews for the moment.

    Write your review
    Rustoleum - Hard Hat - Fluorescent Topcoat

    13 other products in the same category:

    arrow_back
    arrow_forward
    Rustoleum - Hard Hat - Fluorescent Topcoat

    Rustoleum - Hard Hat - Fluorescent Topcoat

    £13.24
    Tax excluded
    £15.89 Tax incl.
    Delivered Within 3-5 Days