We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

    PPG - Sigmashield 880 - Epoxy Coating

    Review (0)
    £66.20
    Tax excluded
    £79.44 Tax incl.

    PPG - Sigmashield 880 is a two-component, high-build polyamine adduct cured epoxy coating, primarily designed for use in offshore splashzone maintenance.

    Custom Colour

    Please enter your required colour into the box below and click Submit Colour
    You can find our colour charts here
    • 250 char. max
    Size :
    Product Group :
    Finish :
    Quantity :
    • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
    • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

    PPG - Sigmashield 880 is a two-component, high-build polyamine adduct cured epoxy coating, primarily designed for use in offshore splashzone maintenance.

    Features

    • Primarily designed for use in offshore splash zone maintenance
    • Outstanding sea water resistance
    • Excellent corrosion resistance
    • Surface tolerant and abrasion resistant
    • Continues to cure when immersed in water
    • Long-term protection in a single-coat application
    • Resistant to well designed cathodic protection
    • Suitable for application on exterior of buried pipes
    • Suitable on wet blast or ultra high pressure water (UHPWW) cleaned substrates (damp or dry)

    Recommended Substrate Conditions and Temperatures

    Substrate conditions

    • Coating performance will depend upon the surface preparation degree
    • For atmospheric service, abrasive blast to ISO-Sa2½ or minimum SSPC SP-6, power tool cleaned to ISO-St3 (SSPC SP-3)
      or hand tool cleaned to ISO-St2 (SSPC SP-2) or ultra high pressure water jet to SSPC SP WJ-2(L) / NACE WJ-2(L)
    • For immersion service: steel; blast cleaned to ISO-Sa2½ (SSPC SP-10), blasting profile 40 – 75 µm (1.6 – 3.0 mils)
    • Higher profiles (>75 microns, 3.0 mils) is allowable with appropriate coating thickness
    • Compatible previous coat must be dry and free from any contamination

    Note: Coating performance is, in general, proportional to the degree of surface preparation.

    Substrate temperature and application conditions

    • Substrate temperature during application should be at least 3°C (5°F) above dew point

    Instructions For Use

    Mixing ratio by volume: base to hardener 75:25 (3:1)

    • Thinner should be added after mixing the components
    • Do not thin more than is required by appropriate application property
    • Adding too much thinner results in reduced sag resistance and slower cure

    Air spray

    Recommended thinner

    THINNER 91-92

    Volume of thinner

    4 - 8%, depending on required thickness and application conditions

    Nozzle orifice

    1.5 – 3.0 mm (approx. 0.060 – 0.110 in)

    Nozzle pressure

    0.2 - 0.4 MPa (approx. 2 - 4 bar; 29 - 58 p.s.i.)

    Airless spray

    Recommended thinner

    THINNER 91-92

    Volume of thinner

    0 - 8%, depending on required thickness and application conditions

    Nozzle orifice

    Approx. 0.53 – 0.69 mm (0.021 – 0.027 in)

    Nozzle pressure

    15.0 MPa (approx. 150 bar; 2176 p.s.i.)

    Brush/roller

    Recommended thinner

    THINNER 91-92

    Volume of thinner

    0 – 5%

    Cleaning solvent

    THINNER 90-53

    PPG Paints
    PPG-S880

    Data sheet

    Type
    Epoxy
    Size
    4L & 20L
    Colour
    Tintable to many colours
    Finish
    Gloss
    Coverage
    4.3 m²/l for 200 µm (170 ft²/US gal for 8.0 mils)
    For Use On
    Metal
    Application Method
    Brush, Roller & Spray

    Specific References

    No customer reviews for the moment.

    Write your review
    PPG - Sigmashield 880 - Epoxy Coating

    You might also like

    16 other products in the same category:

    arrow_back
    arrow_forward

    PPG - Sigmashield 880 - Epoxy Coating

    £66.20
    Tax excluded
    £79.44 Tax incl.