We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

    PPG - SigmaGuard CSF 585 - Internal Tank Coating
    • PPG - SigmaGuard CSF 585 - Internal Tank Coating

    PPG - SigmaGuard CSF 585 - Internal Tank Coating

    Review (0)
    £116.19
    Tax excluded
    £139.43 Tax incl.

    PPG - SigmaGuard CSF 585 - Internal Tank Coating is a two component, solvent free, epoxy coating designed for internal coating of tanks.

    Size :
    Colour :
    Quantity :
    • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
    • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

    PPG - SigmaGuard CSF 585 - Internal Tank Coating is a two component, solvent free, epoxy coating designed for internal coating of tanks.

    Features

    • Tank coating for drinking water
    • Can be applied by single feed, airless spray equipment
    • Reduced explosion risk and fire hazard
    • Good visibility in confind space due to light colour
    • Suitable for storage of drinking water up to 60c with Sigmacover 522 Primer
    • Approved for drinking water by: Kiwa Holland
    • Meets NSF/ANSI Standard 61 for potable water when applied and used in accordance with the terms described on the NSF website

    Recommended Substrate Conditions and Temperatures

    Carbon steel

    • Steel; blast cleaned to ISO-Sa2½, blasting profile 50 – 100 µm (2.0 – 4.0 mils)
    • If a holding primer is required SIGMACOVER 280 (DFT of 50 µm (2.0 mils)) or SIGMAPRIME 200 (DFT of 75 µm (3.0 mils)) should be used

    Concrete

    • Remove grease, oil and other penetrating contaminants according to ASTM D4258
    • Abrade the surface per ASTM D4259 to remove all chalk and surface glaze or laitance. Achieve surface profile - ICRI CSP 3 to 5
    • AMERCOAT 114 A may be used as a pit filler for certain applications. Check with PPG Technical Service for guidance on chemical resistance
    • Maximum recommended moisture transmission rate is 3 lbs / 1,000 ft2 / 24 hours by moisture transmission test (ASTM F1869, calcium chloride test or by ASTM D4263, plastic sheet test)
    • Alternatively, ASTM D4944 (Calcium Carbide Gas method) can be used, moisture content should not exceed 4%

    Substrate temperature and application conditions

    • Substrate temperature during application and curing should be above 10°C (50°F)
    • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point

    Instructions For Use

    Mixing ratio by volume: base to hardener 77.5:22:5

    • At lower temperature, the viscosity will be too high for spray application
    • The temperature of the mixed base and hardener should preferably be at least 20°C (68°F)
    • No thinner should be added
    • For recommended application instructions, see working procedure

    Airless spray

    • Use heavy-duty, single-feed, airless spray equipment, preferably 60:1 pump ratio and suitable high-pressure hoses
    • In-line heating or insulated hoses may be necessary to avoid cooling down of paint in hoses at low air temperature
    • Application with 45:1 airless spray equipment is possible, provided in-line, heated high-pressure hoses are used
    • Length of hoses should be as short as possible

    Recommended thinner

    No thinner should be added

    Nozzle orifice

    Approx. 0.53 mm (0.021 in)

    Nozzle pressure

    At 20°C (68°F) paint temperature min. 28.0 MPa (approx. 280 bar; 4061 p.s.i.). At 30°C (86°F) min. 22.0 MPa (approx. 220 bar;
    3191 p.s.i.)

    Note: In case of using 45:1 airless spray equipment, the paint must be heated to approximately 30°C (86°F) in order to obtain
    the right application viscosity

    Brush/roller

    • Brush: for stripe coating and spot repair only

    Recommended thinner

    No thinner should be added

    Cleaning solvent

    THINNER 90-83 (preferred) or THINNER 90-53

    Note: All application equipment must be cleaned immediately after use. Paint inside the spraying equipment must be removed
    before the pot life has been expired.

    PPG Paints
    PPG-SC5

    Data sheet

    Type
    Epoxy
    Size
    4L & 20L
    Colour
    Blue & White
    Finish
    Gloss
    Coverage
    3.3 m²/l for 300 µm (134 ft²/US gal for 12.0 mils)
    For Use On
    Multi-Surface
    Application Method
    Brush, Roller & Spray

    Specific References

    No customer reviews for the moment.

    Write your review
    PPG - SigmaGuard CSF 585 - Internal Tank Coating

    You might also like

    7 other products in the same category:

    arrow_back
    arrow_forward
    PPG - SigmaGuard CSF 585 - Internal Tank Coating

    PPG - SigmaGuard CSF 585 - Internal Tank Coating

    £116.19
    Tax excluded
    £139.43 Tax incl.