We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

    Axalta - ViterBond WG500 Epoxy Primer
    • Axalta - ViterBond WG500 Epoxy Primer

    Axalta - ViterBond WG500 HS Epoxy Int/Finish

    Review (0)
    £95.92
    Tax excluded
    £115.10 Tax incl.

    ViterBond WG500 HS Epoxy Int/Finish by Axalta is a two pack epoxy, high-solids, low-temperature curing intermediate/finish.


    Custom Colour

    Please enter your required colour into the box below and click Submit Colour
    You can find our colour charts here
    • 250 char. max
    Size :
    Product Group :
    Finish :
    Quantity :
    • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
    • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

    ViterBond WG500 Epoxy Primer by Axalta is a two pack epoxy, high-solids, low-temperature curing intermediate/finish.


    Features and Use:

    • Cures down to 2oC.
    • Use as a rust inhibiting primer on hand prepared steel, or as a high build patch repair primer under most generic coating types.
    • Excellent anticorrosive protection.
    • Excellent ‘wetting’ properties for application to a manually prepared steel surface.
    • Good chemical and solvent resistance.
    • Use to upgrade a conventional system to high performance epoxy/polyurethane.
    • Can overlap onto aged, sound chlorinated rubber, vinyl or alkyd products.

    Surface Preparation:

    • All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams.
    • Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns.
    • Where blast cleaning is impractical the surface should be prepared to St2 (ISO 8501-1:2007) taking care to avoid ‘polishing’ the surface.
    • Can be used as a brush or spray applied primer when water abrasive blast cleaning. Allow to dry and lightly wire brush if powdery deposits form.


    Mixing:


    Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator. Agitate periodically during use to ensure product remains homogeneous.


    Application Conditions:

    Only apply in conditions of good ventilation which must be maintained during drying and curing. Do not apply when rain, mist, sleet or snow are imminent. During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3oC above the dew point. Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process.


    Application Methods:

    • Airless Spray: Output fluid pressure at tip 2000-3000 psi, Tip Size: 19-27 thou (0.48-0.68mm).
    • Apply by brush over manually prepared bare steel surfaces.
    • If applying by brush over blast cleaned steel, take care not to brush the coating off the peaks, or apply two brush coats for safety.
    • Refer to Spencer ‘Epoxy Application and Curing Notes’.
    Axalta Coating Systems
    AXA-VWEP

    Data sheet

    Type
    Epoxy
    Size
    5L
    Colour
    Tintable to many colours
    Finish
    High Sheen
    For Use On
    Steel
    Application Method
    Airless Spray / Brush

    Specific References

    No customer reviews for the moment.

    Write your review
    Axalta - ViterBond WG500 HS Epoxy Int/Finish

    16 other products in the same category:

    arrow_back
    arrow_forward
    Axalta - ViterBond WG500 Epoxy Primer

    Axalta - ViterBond WG500 HS Epoxy Int/Finish

    £95.92
    Tax excluded
    £115.10 Tax incl.