We use cookies to improve your experience on our website. By browsing this website, you agree to our use of cookies.  Learn More

  • New
PPG - Sigmazinc 109 HS - Zinc Epoxy Primer
  • PPG - Sigmazinc 109 HS - Zinc Epoxy Primer

PPG - Sigmazinc 109 HS - Zinc Epoxy Primer

Review (0)
£237.60
Tax excluded
£285.12 Tax incl.

PPG - Sigmazinc 109 HS is a two component high solids polyamide adduct cured zinc epoxy primer designed as a system primer for various paint systems.

Size :
Colour :
Quantity :
  • Secure Payments - Payments safe and secure as all transactions are encrypted to the highest global standard.
  • Delivery policy - We aim to ship all products same day where possible (Orders must be placed before 12pm)

PPG - Sigmazinc 109 HS is a two component high solids polyamide adduct cured zinc epoxy primer designed as a system primer for various paint systems.

Features

  • Excellent anticorrosive properties
  • Quick-drying, can be overcoated after a short interval
  • Can serve as a holding primer for various maintenance systems for a total repair
  • Very good primer for systems with high solids epoxy buildcoats
  • Complies with SSPC-Paint 20 level 2 and ISO 12944.5

Recommended Substrate Conditions and Temperatures

Immersion exposure

  • Steel; blast cleaned to ISO-Sa2½, blasting profile 40 – 70 µm (1.6 – 2.8 mils)
  • Steel with approved zinc silicate shop primer; pretreated according to SPSS-Ss

Atmospheric exposure conditions

  • Steel; blast cleaned to ISO-Sa2½, blasting profile 40 – 70 µm (1.6 – 2.8 mils)
  • Steel with approved zinc silicate shop primer pretreated according to SPSS or power tool cleaned to SPSS-Pt3

Substrate temperature

  • Substrate temperature during application and curing down to 0°C (32°F) is acceptable; provided the substrate is free from ice and dry
  • Substrate temperature during application and curing should be at least 3°C (5°F) above dew point

Instructions For Use

Mixing ratio by volume: base to hardener 80:20 (4:1)

  • The temperature of the mixed base and hardener should preferably be above 15°C (59°F), otherwise extra thinner may be required to obtain application viscosity
  • Adding too much thinner results in reduced sag resistance and slower cure
  • Thinner should be added after mixing the component

Air spray

Recommended thinner

THINNER 91-92

Volume of thinner

0 - 15%, depending on required thickness and application conditions

Nozzle orifice

1.8 – 2.2 mm (approx. 0.070 – 0.087 in)

Nozzle pressure

0.3 - 0.6 MPa (approx. 3 - 6 bar; 44 - 87 p.s.i.)

Airless spray

Recommended thinner

THINNER 91-92

Volume of thinner

0 - 15%, depending on required thickness and application conditions

Nozzle orifice

Approx. 0.43 – 0.48 mm (0.017 – 0.019 in)

Nozzle pressure

15.0 MPa (approx. 150 bar; 2176 p.s.i.)

Brush/roller

Recommended thinner

THINNER 91-92

Volume of thinner

0 – 10%

Cleaning solvent

THINNER 90-53

PPG Paints
PPG-S1HZEP

Data sheet

Type
Epoxy
Size
8L
Colour
Red Grey
Finish
Flat
Coverage
11 m²/L
For Use On
Metal
Application Method
Brush, Roller & Spray
Interior/Exterior
Exterior

Specific References

No customer reviews for the moment.

Write your review
PPG - Sigmazinc 109 HS - Zinc Epoxy Primer

You might also like

4 other products in the same category:

arrow_back
arrow_forward
PPG - Sigmazinc 109 HS - Zinc Epoxy Primer

PPG - Sigmazinc 109 HS - Zinc Epoxy Primer

£237.60
Tax excluded
£285.12 Tax incl.